Model 900VSX - quality from top to bottom and famous Onsrud Inverted Router design

Onsrud Inverted Routers® have set a new standard for versatility, performance and ease of operation. The finest quality work can now be accomplished in less time--without the headaches normally associated with conventional overhead routers.

The model 900VSX is Onsrud's finest machine, ruggedly built to the highest quality specifications. Only the very best components are incorporated in this tough, dependable machine, assuring you many years of precision performance.

Onsrud Inverted Router design means:

• Cutter enters workpiece from underneath.
• Pattern and guide pin are on top for easy reference--in full view of the operator.
• Greater stability on the workpiece and cutter, resulting in smoother cuts and easier work.
• Depth register is more accurate using the fixed position of the table as the reference point.
• Workpiece cannot be "pulled" into a spiral bit (the way it can sometimes be pulled into an overhead bit).
• Under-the-table vacuum sawdust and chip removal system works with gravity to keep sawdust and chips out of the way--even on deep cuts--eliminating the major cause of bit chatter and burns. It also increases feed rate and tool life.
• There are many other benefits to Onsrud Inverted Router©design. See the Onsrud videos entitled "The Inverted Router" and "Template Making" for more details.

• Oversized pulleys for better power transmission.
• Precision spindle machined and ground from special alloy steel for accuracy, rigidity and long life.
• Quick change pulleys for the ultimate in precision and convenience. Your operators can machine their pieces at exactly the right rpm for any application!
• A replaceable 3/4" chuck assembly that allows replacement of a damaged chuck without replacing the whole spindle shaft.
• Automatic shutdown when there is insufficient air pressure to operate spindle lubrication/cooling system.
• Interlocks that require prelubrication of the spindle bearings and appropriate drive belt tensioner setting before the spindle may be started.
• Magnetic starter with adjustable "circuit breaker" type overload protection and switched automatic or manual reset.
• Aircraft grade ABEC 7 Precision "BARDEN" brand spindle bearings rated for 30,000 rpm.
• A totally enclosed, fan cooled, three phase heavy duty 10 horsepower motor for a maximum spindle speed of 25,000 rpm, variable with quick change pulleys or optional "high cycle" solid state drive.
• Spindle travel of 0-3" by pneumatic valve.
• Fog mist lubricated, compressed air cooled extra heavy duty cutting spindle.
• Automatic brake.
• A three position depth stop, infinitely adjustable and conveniently located for quick, easy and accurate setups.
• Standard accessories including a full complement of set-up wrenches, instruction manual, lubrication gun, 1/4", 5/16", 3/8", 1/2" guide pins and 1/4", 3/8" and 1/2" collet.
• Unlimited sizes of simple and inexpensive guide pins available as optional accessories.
• Full one year limited warranty.
• A 31" x 43" x 1 1/2" acrylic-topped table that absorbs cutting vibrations without marring the workpiece.
• Direct factory "Hot Line" for technical support.
• With an Onsrud 900VSX Inverted Router® you can craft intricate patterns in a single pass. A workpiece can be processed at a variety of depths with the tightly secured template always in view for maximum accuracy. The ultimate machine from Onsrud allows you to produce the finest quality work while dramatically increasing the volume your cutting room can handle.

• Model 900VSX (with pneumatic foot pedal to actuate the cutter spindle)

• Lower depth stop
• Intri-shaper option
• Infinitely variable speed control
• Vacuum template system
• Table fence

• Throat depth: 36" (914 mm)
• Table size: 43" x 31" (1100 mm x 780 mm)*
• Maximum workpiece/template height: 4" (100 mm)*
• Dust collection: 500 CFM (2000 m³/h), 4" (100 mm) outlet
• Compressed air: 80 psi (6 bar), 4 CFM (150 liters/minute)
• Motor: 10 horsepower, 3 phase
• Shipping weight: 1900 lbs. (862 kg.)